|
|
Frequent flyer Gold
Posts: 1093
   
Location: An island off southern Tasmania. | Simply fire up the software with a laptop comport connected to the SMT6.
Only pins 2 and 3 are required to be connected, it uses XON/XOFF RS232 protocol.
Pin 5, the ground is also connected.
So...a 3 wire rs232 cable.
Refer to the SMT6 manual.
Fire up the application software for windows XP, hover the mouse over the RPM menu bar....press and hold the right mouse button for 10 seconds and a pop up menu will appear asking if you want to UNLOCK.
A dialogue box should pop up asking you if you want to clear the contects.
That's it..no need to buy an unlocked SMT6.
It will wipe all the screens if you unlock.
You will need to enter the following screens manually....your car will not run properly until you do.
The following screens are as delivered with a stock TMR380 Sprintex kit from TMR.
 (global analog.JPG)
 (global config.JPG)
 (global cylinders.JPG)
 (global ignition.JPG)
 (global modes.JPG)
 (global speed.JPG)
 (global switch.JPG)
 (global.JPG)
 (analog.JPG)
 (ignition.JPG)
 (injection.JPG)
 (sensor.JPG)
Attachments
----------------
 global analog.JPG (29KB - 613 downloads)
global config.JPG (35KB - 638 downloads)
global cylinders.JPG (19KB - 590 downloads)
global ignition.JPG (30KB - 626 downloads)
global modes.JPG (31KB - 601 downloads)
global speed.JPG (21KB - 628 downloads)
global switch.JPG (24KB - 611 downloads)
global.JPG (29KB - 646 downloads)
analog.JPG (119KB - 629 downloads)
ignition.JPG (120KB - 622 downloads)
injection.JPG (120KB - 679 downloads)
sensor.JPG (81KB - 610 downloads)
|
|
| |
|
Frequent flyer Gold
Posts: 421
Location: Brisbane,qld | I cant work it out, got the right lead both software and lead are on com 1 still doesnt connect,i done the unlock thing and it said it deleted the stored map but nothing happened, ive done this many times with my bike, im lost????????????????? |
|
| |
|
Frequent flyer Gold
Posts: 1093
Location: An island off southern Tasmania. | wsbtt - 18/10/2011 18:07
I cant work it out, got the right lead both software and lead are on com 1 still doesnt connect,i done the unlock thing and it said it deleted the stored map but nothing happened, ive done this many times with my bike, im lost?????????????????
windows XP?
dont even dream about using vista or win7 for stuff like this....
you also have to write commit to the ecu after making changes |
|
| |
|
Frequent flyer Gold
Posts: 421
Location: Brisbane,qld | Well thats half my problem, whats "write commit" by the way? |
|
| |
|
Frequent flyer Gold
Posts: 1093
Location: An island off southern Tasmania. | wsbtt - 18/10/2011 22:31
Well thats half my problem, whats "write commit" by the way?
after you make the changes on the screens you have to say you want to save it to the ecu, cause it doesnt save to ecu by default. |
|
| |
|
Frequent flyer Gold
Posts: 421
Location: Brisbane,qld | so does that come up automatically or do i find that under the file menu |
|
| |
|
Frequent flyer Gold
Posts: 1093
Location: An island off southern Tasmania. | wsbtt - 19/10/2011 07:39
so does that come up automatically or do i find that under the file menu
You will find it under the file menu.
You do know that you can drive around and alter the map settings in real time don't you?
If you have an assistant it will highlight the exact map cell on the tune that matches your speed,revs,etc and you can tweak it with instant results....
better than a dyno....but be careful..full throttle can be daunting while operating a laptop...LOL
Bear in mind what you are doing here...we are only talking about the 7th injector enrichment...not the main injectors. |
|
| |
|
Frequent flyer Gold
Posts: 421
Location: Brisbane,qld | Thanks for that, much appreciated, i noticed Foozcool , ithink thats how its spelt, has replaced the 7th injector for water \meth injection and uped the size of the main injectors , does this make for a better setup? oh yeah, one thing i was going to ask you ,have you saved you map to file at all, would be easier to do it that way if you have as punching all the settings manualy takes a bit????
Edited by wsbtt 19/10/2011 12:27
|
|
| |
|
Frequent flyer Gold
Posts: 516
| wsbtt - 19/10/2011 12:23
Thanks for that, much appreciated, i noticed Foozcool , ithink thats how its spelt, has replaced the 7th injector for water \meth injection and uped the size of the main injectors , does this make for a better setup? oh yeah, one thing i was going to ask you ,have you saved you map to file at all, would be easier to do it that way if you have as punching all the settings manualy takes a bit????
I tried...but when you try to use it on another copy of the software it doesnt take it.
Probably why sprintex only gave us photos of the screens as well.
It's only 10 minutes work...dead easy.
Rob aka Fooz has a different piggyback ECU so meth injection supported. |
|
| |
|
Frequent flyer Gold
Posts: 421
Location: Brisbane,qld | z80 - 19/10/2011 23:20
wsbtt - 19/10/2011 12:23
Thanks for that, much appreciated, i noticed Foozcool , ithink thats how its spelt, has replaced the 7th injector for water \meth injection and uped the size of the main injectors , does this make for a better setup? oh yeah, one thing i was going to ask you ,have you saved you map to file at all, would be easier to do it that way if you have as punching all the settings manualy takes a bit????
I tried...but when you try to use it on another copy of the software it doesnt take it.
Probably why sprintex only gave us photos of the screens as well.
It's only 10 minutes work...dead easy.
Rob aka Fooz has a different piggyback ECU so meth injection supported. |
|
| |